8 Inputs for AC/DC 12...230 V
Модель: 5WG12631EB01Цена:
В корзину
Перейдите в каталог, выберите требуемый товар и добавьте его в корзину.
Или просто Отправьте заявку
Метка — Gamma instabus - KNX.
-One output for switching and dimming resistive, inductive or capacitive loads -With semiconductor output for switching and dimming of lamps -Rated operational voltage AC 230 V, 50/60 Hz -Connected load 50...210 VA -Settable switching and dimming behaviour -Selectable mode of operation (normal mode, timer mode) -Soft on, Soft off -Dimming or jumping to a new dimming value -Time-delayed switch-off when dimming below a settable dimming value -Status objects for switching and dimming value -Short-circuit message -Message of a load failure -Integrated 8-bit scene control -Object for blocking the output -Configurable brightness value at start and end of a blocking phase -Adjustable behaviour of the output after bus voltage recovery -2 binary inputs for potential-free contacts -Selectable function of the binary inputs: acting as secondary inputs directly on the switching outputs or acting as independant binary inputs with bus communication -Free allocation of the functions switching, dimming, solar protection control, send value and scene control to the inputs -Two independent switching objects per input -Blocking object for each input -Separately selectable behaviour per input at bus voltage recovery -Telegram rate limitation for both inputs -About 20 cm long wires for connecting phase conductor, output, inputs and bus -Bus-powered electronics -Integrated bus coupling unit -Enclosed bus terminal for bus connection -For installation in a flush-mounting wall or ceiling box with 60 mm diameter
Модель: 5WG15252AB31Dimmer output 20...1000 VA, parallel operation of the outputs for doubling the dimming power to 40...2000 VA
Модель: 5WG15271AB51-8 DALI outputs -Control capacity for up to 8 DALI-ECGs per DALI output -Power supplied to the electronics and the DALI outputs through an integrated power supply unit for 230 V AC -Green LED for status display -Pushbutton for selecting and switching over 4 DALI outputs respectively between bus and direct mode -Yellow LED for indicating which 4 DALI outputs the direct mode is activated for -1 red LED per DALI output for indicating the circuit state or fault (e.g. lighting medium failure) of the connected group -Four pushbutton pairs for switching and dimming of 4 DALI outputs in direct mode, functional when 230 V AC is applied (also when no bus voltage is connected and also when bus communication has not yet been started or is interrupted) -Selection of identical or individual configuration of all DALI outputs -Selectable operating mode per DALI output (normal mode, 1-level or 2-level time-switch mode) -Per DALI output with command objects for switching on/off, dimming brighter/darker and setting dimming value -Per DALI output optionally with up to 4 add-on status objects (circuit state and lighting medium failure, dimming value status and DALI status) -Sending of status objects on request and/or automatically after change -Per DALI output with add-on object for time-limited switching on of lighting in night mode (cleaning light) -Warning approx. 1 minute before imminent switching off, by dimming to 50 % of former dimming value in night or timer mode -Adjustable switching on and/or off of a channel through dimming brighter/darker, dimming value when switching on, actuating or dimming a new dimming value, dimming time from 0% to 100% -Adjustable behavior on bus voltage or mains voltage failure and bus voltage or mains voltage recovery -Add-on object and integrated 8bit scene control for saving and restoring up to 16 scenes per DALI output -Integrated bus coupling unit as only half standard bus load -Bus connection through bus terminal as well as contact system to data rail -Device for mounting on rail TH35 DIN EN 60715 The data rail must be ordered separately. See chapter system products and accessories - data rails.
Модель: 5WG15251EB01-For switching and dimming of eight mutually independent groups (channels) of fluorescent lamps with dimmable electronic control gear (ECG) -8 control voltage outputs 1...10 V DC -Control power min. 60 OSRAM ECG dynamic each -8 switching outputs (relay contacts) for 230 V AC, 50/60 Hz, 16 A at p.f. = 1 -Each of them for connection of min. 30 OSRAM ECG dynamic for 58 W fluorescent lamps -Slide switch per relay output for manual operation and switch position indication -Selection between identical or individual configuration of all channels -Command objects for each actuator channel for switching on/off, dimming brighter/darker and set/value -One 1-bit and one 8-bit-status object (switching state and dimming value) per output -Per channel configurable time-limited activation of the lighting during night mode (base lighting) -Warning 30 seconds prior to imminent switch off by dimming to 50 % of the previous dimming value for each channel with time-limited operation -Switching on or off of a channel by dimming brighter/darker -Configurable dimming value upon switching on -Jumping or dimming to a new dimming value -Configurable dimming time from 0...100% -Integrated 8 bit scene control and assignment of each output to up to 8 scenes -Transmission of status objects on request, cyclically and/or automatically after changes -Configurable behaviour on bus voltage failure and recovery -Bus-powered electronics -Integrated bus coupling unit, bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The data rail must be ordered separately. See chapter system products and system accessories - data rails.
Модель: 5WG15261EB02-For covering free data rail segments (in accordance with the SELV regulations for safety extra-low voltage) -For snapping onto standard mounting rails, separable, RAL 7035 -Length 13.5 MW (1 MW = 18 mm)
Модель: 5WG11928AA01For the protection of already installed flush-mounting bus coupling units, DELTA bus coupling units or flush-mounting actuators with user interface (UI) through to the mounting of bus terminals
Модель: 5WG11962AB01-For four Pt1000 sensors -For the measurement and transmission of 4 temperatures in the range -40...+150 °C -For connection of four Pt1000 temperature sensors2), each via a 2-wire cable up to 50 m in length -Configurable smoothing of a measured value through mean value generation -Monitoring of a lower and upper limit value for each measured value, with configurable hysteresis for limit value signals -Electronics powered via an integrated power supply unit for 230 V AC -Green LED for displaying ready-to-run status -Integrated bus coupling units -Bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The accompanying physical sensors must be ordered separately. See chapter Physical sensors - sensors without KNX connection.The data rail must be ordered separately. See chapter System Products and Accessories - data rails.
Модель: 5WG12581AB022 facing pushbutton rockers Аксессуары для клавиш UP223 и UP287 с ИК-приёмником и декодером
Модель: 5WG14203AB134 facing pushbutton rockers Аксессуары для клавиш UP223 и UP287 с ИК-приёмником и декодером
Модель: 5WG14213AB13