-Used as passive infrared detector for indoor ceiling installation -Sensing range, horizontal 360 °, vertical approx. 80 ° -For monitoring an area with a diameter of approx. 4 m to approx. 7 m (depending on mounting and room height) -LED on sensor head for display -Used as brightness sensor -Cone–shaped detection area, opening angle 90 ° -Measuring range 20 to 1000 lx -Integrated DALI bus coupling unit for communicating with a central DALI controller -Power supply through DALI line with 5 mA DALI bus load -Plug-in terminals for connecting the DALI line -For installation in suspended ceilings

-Binary input device -4 inputs to connect installation buttons -Supported actions per input -Short button press -Long button press -Integrated DALI bus coupling unit for communicating with a central DALI controller -Power supply through DALI line with 6 mA DALI bus load -For flush-mounting wall or ceiling outlet installations with a 60 mm diameter and depth of 60 mm -Plug-in terminals for connecting the DALI line -Cable set for connecting pushbuttons

-8 DALI outputs -Control capacity for up to 8 DALI-ECGs per DALI output -Power supplied to the electronics and the DALI outputs through an integrated power supply unit for 230 V AC -Green LED for status display -Pushbutton for selecting and switching over 4 DALI outputs respectively between bus and direct mode -Yellow LED for indicating which 4 DALI outputs the direct mode is activated for -1 red LED per DALI output for indicating the circuit state or fault (e.g. lighting medium failure) of the connected group -Four pushbutton pairs for switching and dimming of 4 DALI outputs in direct mode, functional when 230 V AC is applied (also when no bus voltage is connected and also when bus communication has not yet been started or is interrupted) -Selection of identical or individual configuration of all DALI outputs -Selectable operating mode per DALI output (normal mode, 1-level or 2-level time-switch mode) -Per DALI output with command objects for switching on/off, dimming brighter/darker and setting dimming value -Per DALI output optionally with up to 4 add-on status objects (circuit state and lighting medium failure, dimming value status and DALI status) -Sending of status objects on request and/or automatically after change -Per DALI output with add-on object for time-limited switching on of lighting in night mode (cleaning light) -Warning approx. 1 minute before imminent switching off, by dimming to 50 % of former dimming value in night or timer mode -Adjustable switching on and/or off of a channel through dimming brighter/darker, dimming value when switching on, actuating or dimming a new dimming value, dimming time from 0% to 100% -Adjustable behavior on bus voltage or mains voltage failure and bus voltage or mains voltage recovery -Add-on object and integrated 8bit scene control for saving and restoring up to 16 scenes per DALI output -Integrated bus coupling unit as only half standard bus load -Bus connection through bus terminal as well as contact system to data rail -Device for mounting on rail TH35 DIN EN 60715 The data rail must be ordered separately. See chapter system products and accessories - data rails.

-For communication via KNX EIB with electronic ballasts with a DALI interface -DALI output acc. to IEC 60929, for communication with up to 64 DALI ballasts -Integrated power supply with input voltage AC/DC 110...240 V, 50...400 Hz, for powering the gateway electronics and DALI output -Maximum DALI output voltage of 16 V, short circuit resistant -Green LED for displaying the operating voltage -Pushbutton for switching between bus and direct operating mode -Yellow LED for displaying direct mode -One pair of push buttons for switching On/Off of all connected DALI ballasts -One red LED in the switching button for displaying the switching state of all DALI ballasts (permanent LED light) and displaying a DALI fault condition by blinking -Control (switching, dimming, and setting dimming value) as well as feedback of status and lamp failure of up to 64 DALI ballasts -Operation of each DALI ballast either as individual device or as member of one of up to 16 DALI groups -Configurable assignment of the DALI ballasts to up to 16 DALI groups, which can only be switched and dimmed in groups including reporting status and lamp failures in groups -Control (switching, dimming, setting dimming value) of self-contained emergency luminaires as individual luminaires or as member of a DALI group -Distinction between self-contained emergency luminaires with one or two DALI devices -Starting the self-conducted testing of each individual inverter and reporting the test result via bus -Distinction between function test, short duration test, and long duration test -Optional configuration of any DALI ballast to dim to a preset dimming value in case of emergency mode -Locking of switching and dimming commands as well as configuration while emergency mode is activated -Activation of emergency mode based on a configurable number of failed DALI ballasts -Transformation of dimming commands into a temporary set point adjustment for ballasts with integrated constant light level control and directly connected light level sensor -One or two level timer -Integrated scene control for up to 16 scenes -Integrated one time or cyclical control of repeatable sequences or color effects -Possible assignment of a CIN to a DALI ballast and with commissioning of DALI ballasts and test of channel, scene, and effect functionality within ETS -Integrated bus coupling unit -Only half a standard bus load -Bus connection via bus terminal or contact system to data rail -For mounting on DIN rail EN 60715-TH35-7.5 The data rail must be ordered separately. See chapter System Products and Accessories - data rails.