Electromotive, proportional (constant) valve actuator with LED valve position indication and with integrated bus coupling unit for direct connection to KNX: -For latching to valve adapter -Delivery with valve adapter rings suitable for Siemens (VDN../VEN.., VPD../VPE.., VD...CLC, V..I46.., V..P47..) Danfoss RA, Heimeier, MNG, Schl?sser ab 3/93, Honeywell, Braukmann, Dumser (distribution board), Reich (distribution board), Oventrop, Herb, Onda -Max. positioning force: 120 N -Cable permanently connected to the enclosure for bus connection and two additional signaling contacts (e. g. window contacts), which can be connected as binary inputs -For operation solely with the bus voltage, i. e. without external auxiliary power -Maintenance-free, silent drive -Automatic valve stroke detection, through which the actuator travel is adjusted to the valve used

For mounting a AP 561H valve actuators onto small valve makes Danfoss mit Klemmverbindung

For mounting a AP 561H valve actuators onto small valve makes Danfoss RA2000

For mounting a AP 561H valve actuators onto small valve makes Herz

For mounting a AP 561H valve actuators onto small valve makes Onda

For mounting a AP 561H valve actuators onto small valve makes TA

For mounting a AP 561H valve actuators onto small valve makes Vaillant

-Opening alarm for the monitoring of windows and doors, comprising: -1 magnet (? 8 x 30 mm) -1 magnetically operated contact in a fully cast plastic enclosure (? 8 x 30 mm) -Switching voltage: max. 110 V DC -Switching current: 10...100 mA -Contact current carrying capacity: max. 5 W -Contact resistance: max. 150 mW -VdS-class B -5 m long connection cable LiYY 4 x 0,14 mm2 -Suitable for flush and surface mounting -2 surface-mounting enclosure tops (43 x 12 x 12 mm) -2 surface-mounting enclosure bottoms -4 spacer plates (thickness: 2 x 4 mm or 2 x 2 mm) -2 flush-mounting flanges -4 antimagnetic countersunk self-tapping screws DIN 7982-ST2, 9 x 16-A2

-Opening alarm for the monitoring of windows and doors, comprising: -1 magnet (? 8 x 30 mm) -1 magnetically operated contact in a fully cast plastic enclosure (? 8 x 30 mm) -Switching voltage: max. 110 V DC -Switching current: 10...100 mA -Contact current carrying capacity: max. 5 W -Contact resistance: max. 150 mW -VdS-class B -5 m long connection cable LiYY 4 x 0.14 mm2 -Suitable for flush and surface mounting -2 surface-mounting enclosure tops (43 x 12 x 12 mm) -2 surface-mounting enclosure bottoms -4 spacer plates (thickness: 2 x 4 mm or 2 x 2 mm) -2 flush-mounting flanges -4 antimagnetic countersunk self-tapping screws DIN 7982-ST2, 9 x 16-A2

-For four Pt1000 sensors -For the measurement and transmission of 4 temperatures in the range -40...+150 °C -For connection of four Pt1000 temperature sensors2), each via a 2-wire cable up to 50 m in length -Configurable smoothing of a measured value through mean value generation -Monitoring of a lower and upper limit value for each measured value, with configurable hysteresis for limit value signals -Electronics powered via an integrated power supply unit for 230 V AC -Green LED for displaying ready-to-run status -Integrated bus coupling units -Bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The accompanying physical sensors must be ordered separately. See chapter Physical sensors - sensors without KNX connection.The data rail must be ordered separately. See chapter System Products and Accessories - data rails.

Нет описания

Нет описания

-3 x 230 V AC, 6 A (p.f. = 1) -2 x 24 V AC, 5 W (p.f. = 1) -Electronics powered via an integrated 24 V AC/DC power supply unit -2 signal input (floating contacts), Determination of switching state by means of the voltage generated in the device

-3 x 230 V AC, 6 A (p.f. = 1) -2 x 24 V AC, 15 W (p.f. = 1) -Electronics powered via an external 24 V AC/DC power supply unit -1 signal input (floating contacts), Determination of switching state by means of the voltage generated in the device

230 V AC, deenergized closed, max. lift 3.5 mm AP 561/01 and AP 561/02 are suitable for N 605 and N 650/11 thermal drive actuators, see chapter Heating, Cooling, Ventilation, Air-Conditioning - Actuators for HCVA.

230 V AC, deenergized open, max. lift 2.6 mm AP 561/01 and AP 561/02 are suitable for N 605 and N 650/11 thermal drive actuators, see chapter Heating, Cooling, Ventilation, Air-Conditioning - Actuators for HCVA.

24 V, deenergized closed, max. lift 3.5 mm AP 561/01 and AP 561/02 are suitable for N 605 and N 650/11 thermal drive actuators, see chapter Heating, Cooling, Ventilation, Air-Conditioning - Actuators for HCVA.

24 V, deenergized open, max. lift 2.6 mm AP 561/01 and AP 561/02 are suitable for N 605 and N 650/11 thermal drive actuators, see chapter Heating, Cooling, Ventilation, Air-Conditioning - Actuators for HCVA.