-Used as passive infrared detector for indoor ceiling installation -Sensing range, horizontal 360 °, vertical approx. 80 ° -For monitoring an area with a diameter of approx. 4 m to approx. 7 m (depending on mounting and room height) -LED on sensor head for display -Used as brightness sensor -Cone–shaped detection area, opening angle 90 ° -Measuring range 20 to 1000 lx -Integrated DALI bus coupling unit for communicating with a central DALI controller -Power supply through DALI line with 5 mA DALI bus load -Plug-in terminals for connecting the DALI line -For installation in suspended ceilings

-Binary input device -4 inputs to connect installation buttons -Supported actions per input -Short button press -Long button press -Integrated DALI bus coupling unit for communicating with a central DALI controller -Power supply through DALI line with 6 mA DALI bus load -For flush-mounting wall or ceiling outlet installations with a 60 mm diameter and depth of 60 mm -Plug-in terminals for connecting the DALI line -Cable set for connecting pushbuttons

-6 pushbutton pairs for the remote control of lighting, shutter/blinds and scenes via UP 258E21 or UP 258D11 presence detector -Parameterization is via ETS in the UP 258E21 or UP 258D11 presence detector -Range: approx. 4.5 m -Power supply: CR2025 lithium button cell -Degree of protection (acc. to EN 60529): IP40

-Integrated 2-step light control, optionally available in fully automatic or semi-automatic version -3 independent control channels each with 2 start objects and 2 end objects

-Integrated constant light level control and 2-step light control, optionally available in fully automatic or semi-automatic version -4 channels for offset groups

-Brightness measurement, temperature measurement, sun protection control, lighting control -For the detection and transmission of brightness and temperature -Temperature measuring range -25 °C...+55 °C -Brightness measuring range 1 Lux...100 kLux -Horizontal sensing angle -60°...+60°, vertical -35°...+66.5° -For the control of switch, dimming and shutter/blind actuators, depending on the ambient luminosity and/or ambient temperature -One sun protection channel for the automatic control of sun protection equipment, with -Starting and stopping of automation by means of an object or a dusk threshold -Up to three brightness thresholds for determining the height and position of the shutters/blinds or roller shutters -Optional teach-in of dusk thresholds and brightness thresholds by means of a teach-in facility -Blocking object for the temporary deactivation of the sun protection channel function -Up to four universal channels for the control of switch, dimming and shutter/blind actuators, depending on ambient luminosity and/or temperature. Optionally available with: -Threshold switches for brightness -Threshold switches for temperature -Threshold switches with logical combination of brightness and temperature -Optional teach-in of brightness threshold for each universal channel by means of an associated teach-in facility -Deactivation option for each universal channel by means of an associated blocking object (1 bit) -Optional second object for transmission of a second telegram on fulfillment of threshold conditions -Bus-powered electronics -Integrated bus coupling units -Bus connection via bus terminal -Surface mounting -Degree of protection: IP54 Light level control modules N 342 see chapter Lighting - Light level controls

-For mounting in a hollow-wall or flush-mounting box with diameter 58 mm and min. 40 mm mounting depth -Cover made of white plastic (polystyrene)

-Includes surface-mounting enclosure made of white plastic (polypropylene) with diameter 75 mm and 27 mm in height -For mounting on a ceiling or wall

For direct lighting installation

Dimmer output 20...500 VA

Dimmer output 20...500 VA

Dimmer output 20...1000 VA, parallel operation of the outputs for doubling the dimming power to 40...2000 VA

Dimmer output 20...300 VA

Dimmer output 20...300 VA

-8 DALI outputs -Control capacity for up to 8 DALI-ECGs per DALI output -Power supplied to the electronics and the DALI outputs through an integrated power supply unit for 230 V AC -Green LED for status display -Pushbutton for selecting and switching over 4 DALI outputs respectively between bus and direct mode -Yellow LED for indicating which 4 DALI outputs the direct mode is activated for -1 red LED per DALI output for indicating the circuit state or fault (e.g. lighting medium failure) of the connected group -Four pushbutton pairs for switching and dimming of 4 DALI outputs in direct mode, functional when 230 V AC is applied (also when no bus voltage is connected and also when bus communication has not yet been started or is interrupted) -Selection of identical or individual configuration of all DALI outputs -Selectable operating mode per DALI output (normal mode, 1-level or 2-level time-switch mode) -Per DALI output with command objects for switching on/off, dimming brighter/darker and setting dimming value -Per DALI output optionally with up to 4 add-on status objects (circuit state and lighting medium failure, dimming value status and DALI status) -Sending of status objects on request and/or automatically after change -Per DALI output with add-on object for time-limited switching on of lighting in night mode (cleaning light) -Warning approx. 1 minute before imminent switching off, by dimming to 50 % of former dimming value in night or timer mode -Adjustable switching on and/or off of a channel through dimming brighter/darker, dimming value when switching on, actuating or dimming a new dimming value, dimming time from 0% to 100% -Adjustable behavior on bus voltage or mains voltage failure and bus voltage or mains voltage recovery -Add-on object and integrated 8bit scene control for saving and restoring up to 16 scenes per DALI output -Integrated bus coupling unit as only half standard bus load -Bus connection through bus terminal as well as contact system to data rail -Device for mounting on rail TH35 DIN EN 60715 The data rail must be ordered separately. See chapter system products and accessories - data rails.

-For switching and dimming of eight mutually independent groups (channels) of fluorescent lamps with dimmable electronic control gear (ECG) -8 control voltage outputs 1...10 V DC -Control power min. 60 OSRAM ECG dynamic each -8 switching outputs (relay contacts) for 230 V AC, 50/60 Hz, 16 A at p.f. = 1 -Each of them for connection of min. 30 OSRAM ECG dynamic for 58 W fluorescent lamps -Slide switch per relay output for manual operation and switch position indication -Selection between identical or individual configuration of all channels -Command objects for each actuator channel for switching on/off, dimming brighter/darker and set/value -One 1-bit and one 8-bit-status object (switching state and dimming value) per output -Per channel configurable time-limited activation of the lighting during night mode (base lighting) -Warning 30 seconds prior to imminent switch off by dimming to 50 % of the previous dimming value for each channel with time-limited operation -Switching on or off of a channel by dimming brighter/darker -Configurable dimming value upon switching on -Jumping or dimming to a new dimming value -Configurable dimming time from 0...100% -Integrated 8 bit scene control and assignment of each output to up to 8 scenes -Transmission of status objects on request, cyclically and/or automatically after changes -Configurable behaviour on bus voltage failure and recovery -Bus-powered electronics -Integrated bus coupling unit, bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The data rail must be ordered separately. See chapter system products and system accessories - data rails.

Короб для датчика присутствия: -для монтажа датчика присутствия UP 258/E11 или UP 258/E21 в качестве устройства, монтируемого на поверхность

-Range: up to approx. 4.5 m -Power supply: CR2025 lithium button cell (included in delivery) -Degree of protection (acc. to EN 60529): IP40