-Used as passive infrared detector for indoor ceiling installation -Sensing range, horizontal 360 °, vertical approx. 80 ° -For monitoring an area with a diameter of approx. 4 m to approx. 7 m (depending on mounting and room height) -LED on sensor head for display -Used as brightness sensor -Cone–shaped detection area, opening angle 90 ° -Measuring range 20 to 1000 lx -Integrated DALI bus coupling unit for communicating with a central DALI controller -Power supply through DALI line with 5 mA DALI bus load -Plug-in terminals for connecting the DALI line -For installation in suspended ceilings

-Binary input device -4 inputs to connect installation buttons -Supported actions per input -Short button press -Long button press -Integrated DALI bus coupling unit for communicating with a central DALI controller -Power supply through DALI line with 6 mA DALI bus load -For flush-mounting wall or ceiling outlet installations with a 60 mm diameter and depth of 60 mm -Plug-in terminals for connecting the DALI line -Cable set for connecting pushbuttons

-8 DALI outputs -Control capacity for up to 8 DALI-ECGs per DALI output -Power supplied to the electronics and the DALI outputs through an integrated power supply unit for 230 V AC -Green LED for status display -Pushbutton for selecting and switching over 4 DALI outputs respectively between bus and direct mode -Yellow LED for indicating which 4 DALI outputs the direct mode is activated for -1 red LED per DALI output for indicating the circuit state or fault (e.g. lighting medium failure) of the connected group -Four pushbutton pairs for switching and dimming of 4 DALI outputs in direct mode, functional when 230 V AC is applied (also when no bus voltage is connected and also when bus communication has not yet been started or is interrupted) -Selection of identical or individual configuration of all DALI outputs -Selectable operating mode per DALI output (normal mode, 1-level or 2-level time-switch mode) -Per DALI output with command objects for switching on/off, dimming brighter/darker and setting dimming value -Per DALI output optionally with up to 4 add-on status objects (circuit state and lighting medium failure, dimming value status and DALI status) -Sending of status objects on request and/or automatically after change -Per DALI output with add-on object for time-limited switching on of lighting in night mode (cleaning light) -Warning approx. 1 minute before imminent switching off, by dimming to 50 % of former dimming value in night or timer mode -Adjustable switching on and/or off of a channel through dimming brighter/darker, dimming value when switching on, actuating or dimming a new dimming value, dimming time from 0% to 100% -Adjustable behavior on bus voltage or mains voltage failure and bus voltage or mains voltage recovery -Add-on object and integrated 8bit scene control for saving and restoring up to 16 scenes per DALI output -Integrated bus coupling unit as only half standard bus load -Bus connection through bus terminal as well as contact system to data rail -Device for mounting on rail TH35 DIN EN 60715 The data rail must be ordered separately. See chapter system products and accessories - data rails.

-For switching and dimming of eight mutually independent groups (channels) of fluorescent lamps with dimmable electronic control gear (ECG) -8 control voltage outputs 1...10 V DC -Control power min. 60 OSRAM ECG dynamic each -8 switching outputs (relay contacts) for 230 V AC, 50/60 Hz, 16 A at p.f. = 1 -Each of them for connection of min. 30 OSRAM ECG dynamic for 58 W fluorescent lamps -Slide switch per relay output for manual operation and switch position indication -Selection between identical or individual configuration of all channels -Command objects for each actuator channel for switching on/off, dimming brighter/darker and set/value -One 1-bit and one 8-bit-status object (switching state and dimming value) per output -Per channel configurable time-limited activation of the lighting during night mode (base lighting) -Warning 30 seconds prior to imminent switch off by dimming to 50 % of the previous dimming value for each channel with time-limited operation -Switching on or off of a channel by dimming brighter/darker -Configurable dimming value upon switching on -Jumping or dimming to a new dimming value -Configurable dimming time from 0...100% -Integrated 8 bit scene control and assignment of each output to up to 8 scenes -Transmission of status objects on request, cyclically and/or automatically after changes -Configurable behaviour on bus voltage failure and recovery -Bus-powered electronics -Integrated bus coupling unit, bus connection via bus terminal or contact system to data rail -Modular installation devices for mounting on TH35 EN 60715 mounting rail The data rail must be ordered separately. See chapter system products and system accessories - data rails.